• español
    • English
  • Login
  • español 
    • español
    • English

UniversidaddeCádiz

Área de Biblioteca, Archivo y Publicaciones
Comunidades y colecciones
Ver ítem 
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
JavaScript is disabled for your browser. Some features of this site may not work without it.

Reinforced silica-carbon nanotube monolithic aerogels synthesised by rapid controlled gelation

Thumbnail
Identificadores

URI: http://hdl.handle.net/10498/30363

DOI: 10.1007/s10971-018-4645-7

ISSN: 0928-0707

ISSN: 1573-4846

Ficheros
Reinforced silica-carbon nanotube.pdf (2.391Mb)
Estadísticas
Ver estadísticas
Métricas y Citas
 
Compartir
Exportar a
Exportar a MendeleyRefworksEndNoteBibTexRIS
Metadatos
Mostrar el registro completo del ítem
Autor/es
Morales-Florez, Victor; Piñero de los Ríos, ManuelAutoridad UCA; Mesa Díaz, María del MarAutoridad UCA; Santos Martínez, Deseada María de losAutoridad UCA; Reyes Peces, María VirtudesAutoridad UCA; Díaz-Fraile, José A.; Rosa Fox, Nicolás Daniel de laAutoridad UCA; Esquivia, Luis; Morales Flórez, Víctor
Fecha
2018
Departamento/s
Física de la Materia Condensada; Ingeniería Química y Tecnología de Alimentos
Fuente
Journal of Sol-Gel Science and Technology (2018) 86:391–399
Resumen
This work introduces a new synthesis procedure for obtaining homogeneous silica hybrid aerogels with carbon nanotube contents up to 2.50 wt.%. The inclusion of nanotubes in the highly porous silica matrix was performed by a two-step sol–gel process, resulting in samples with densities below 80 mg/cm3. The structural analyses (N2 physisorption and SEM) revealed the hierarchical structure of the porous matrix formed by nanoparticles arranged in clusters of 100 and 300 nm in size, specific surface areas around 600 m2/g and porous volumes above 4.0 cm3/g. In addition, a relevant increase on the mechanical performance was found, and an increment of 50% for the compressive strength and 90% for the maximum deformation were measured by uniaxial compression. This reinforcement was possible thanks to the outstanding dispersion of the CNT within the silica matrix and the formation of Si–O–C bridges between nanotubes and silica matrix, as suggested by FTIR. Therefore, the original synthesis procedure introduced in this work allows the fabrication of highly porous hybrid materials loaded with carbon nanotubes homogeneously distributed in the space, which remain available for a variety of technological applications.
Materias
Silica hybrid aerogel; Carbon nanotube; Controlled gelation; Structure; Reinforcement; Mechanical properties
Colecciones
  • Artículos Científicos [12059]
  • Articulos Científicos Fis. Mat. Cond. [129]
  • Artículos Científicos IMEYMAT [581]
  • Articulos Científicos Ing. Quim. [314]
Attribution-NonCommercial-NoDerivatives 4.0 Internacional
Esta obra está bajo una Licencia Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 Internacional

Listar

Todo RODINComunidades y ColeccionesPor fecha de publicaciónAutoresTítulosMateriasEsta colecciónPor fecha de publicaciónAutoresTítulosMaterias

Mi cuenta

AccederRegistro

Estadísticas

Ver Estadísticas de uso

Información adicional

Acerca de...Deposita en RODINPolíticasNormativasDerechos de autorEnlaces de interésEstadísticasNovedadesPreguntas frecuentes

RODIN está accesible a través de

OpenAIREOAIsterRecolectaHispanaEuropeanaBaseDARTOATDGoogle Académico

Enlaces de interés

Sherpa/RomeoDulcineaROAROpenDOARCreative CommonsORCID

RODIN está gestionado por el Área de Biblioteca, Archivo y Publicaciones de la Universidad de Cádiz

ContactoSugerenciasAtención al Usuario