• español
    • English
  • Login
  • español 
    • español
    • English

UniversidaddeCádiz

Área de Biblioteca, Archivo y Publicaciones
Comunidades y colecciones
Ver ítem 
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
JavaScript is disabled for your browser. Some features of this site may not work without it.

Effect of the heat treatment on the mechanical properties and microstructure of Scalmalloy® manufactured by Selective Laser Melting (SLM) under certified conditions

Thumbnail
Identificadores

URI: http://hdl.handle.net/10498/30512

DOI: 10.1016/J.MATCHAR.2022.112549

ISSN: 1873-4189

Ficheros
2023_Materials Characterization 196_112549.pdf (2.902Mb)
Estadísticas
Ver estadísticas
Métricas y Citas
 
Compartir
Exportar a
Exportar a MendeleyRefworksEndNoteBibTexRIS
Metadatos
Mostrar el registro completo del ítem
Autor/es
Cabrera Correa, LeticiaAutoridad UCA; González Rovira, LeandroAutoridad UCA; López Castro, Juan de DiosAutoridad UCA; Castillo Rodríguez, MiguelAutoridad UCA; Botana Pedemonte, Francisco JavierAutoridad UCA
Fecha
2023
Departamento/s
Ciencia de los Materiales e Ingeniería Metalúrgica y Química Inorgánica; Ingeniería Mecánica y Diseño Industrial
Fuente
Materials Characterization, Vol. 196, 2023
Resumen
Mechanical properties and microstructure of Scalmalloy® processed by Selective Laser Melting (SLM) under certified conditions are studied. Two types of samples are considered: as-built and heat-treated at 325⁰C for 4 hours. The heat treatment does not modify the grain size or the texture. SEM images show a typical bi-modal microstructure comprising equiaxed fine grained zones (FGZ) with ≈ 0.6 micron grain size and coarse grained zones (CGZ) with ≈ 7.5 micron grain size (longitudinal axis). According to electron backscatter diffraction (EBSD) analysis, FGZ have ≈ 0.8 micron equivalent circle diameter (considering grain boundaries those with misorientation > 15⁰) and contain areas with and without texture, while CGZ have ≈ 2.7 micron equivalent circle diameter, and most of the grains are oriented with [001] crystal direction along the building direction. On the contrary, the heat treatment produces a stress relief that is evidenced in EBSD by reductions in the low angle grain boundaries (LAGB) content, grain orientation spread (GOS), and dislocation density. Both samples show plastic deformation before fracture and the as-built condition features Portevin-Le-Chatelier (PLC) effect. The heat-treated samples exhibit the highest strength (yield strength = 454 ± 3 MPa; tensile strength = 509 ± 6 MPa) and hardness (165 ± 3 HV) while the lowest percentage of reduction of area (16 ± 6%) and elongation (11 ± 2%). Finally, the electrical conductivity of the material increases after the heat treatment which is associated with the redistribution of Mg-atoms out of the solid solution and the growth of precipitates
Colecciones
  • Artículos Científicos [12023]
  • Articulos Científicos CC. Mat. [583]
  • Artículos Científicos IMEYMAT [578]
  • Articulos Científicos Ing. Mec. [327]
Attribution-NonCommercial-NoDerivatives 4.0 Internacional
Esta obra está bajo una Licencia Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 Internacional

Listar

Todo RODINComunidades y ColeccionesPor fecha de publicaciónAutoresTítulosMateriasEsta colecciónPor fecha de publicaciónAutoresTítulosMaterias

Mi cuenta

AccederRegistro

Estadísticas

Ver Estadísticas de uso

Información adicional

Acerca de...Deposita en RODINPolíticasNormativasDerechos de autorEnlaces de interésEstadísticasNovedadesPreguntas frecuentes

RODIN está accesible a través de

OpenAIREOAIsterRecolectaHispanaEuropeanaBaseDARTOATDGoogle Académico

Enlaces de interés

Sherpa/RomeoDulcineaROAROpenDOARCreative CommonsORCID

RODIN está gestionado por el Área de Biblioteca, Archivo y Publicaciones de la Universidad de Cádiz

ContactoSugerenciasAtención al Usuario