• español
    • English
  • Login
  • español 
    • español
    • English

UniversidaddeCádiz

Área de Biblioteca, Archivo y Publicaciones
Comunidades y colecciones
Ver ítem 
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
JavaScript is disabled for your browser. Some features of this site may not work without it.

Noise resistance and shot noise parameters on the study of IGC of aluminium alloys with different heat treatments

Thumbnail
Identificadores

URI: http://hdl.handle.net/10498/30782

DOI: 10.1016/j.electacta.2007.04.094

ISSN: 0013-4686

Ficheros
2007 Electrochimica Acta 52 (6569–6583).pdf (2.094Mb)
Estadísticas
Ver estadísticas
Métricas y Citas
 
Compartir
Exportar a
Exportar a MendeleyRefworksEndNoteBibTexRIS
Metadatos
Mostrar el registro completo del ítem
Autor/es
Sánchez Amaya, José MaríaAutoridad UCA; Bethencourt Núñez, ManuelAutoridad UCA; González Rovira, LeandroAutoridad UCA; Botana Pedemonte, Francisco JavierAutoridad UCA
Fecha
2007
Departamento/s
Ciencia de los Materiales e Ingeniería Metalúrgica y Química Inorgánica
Fuente
Electrochimica Acta 52 (2007) 6569–6583
Resumen
In the present paper, the effect of heat treatment on the susceptibility to intergranular corrosion (IGC) of aluminium alloys is analysed. Samples of aluminium alloys AA2024 and AA7075 were first subjected to different heat treatments. Then the susceptibility of these samples to IGC was determined by means of normalized tests, based on the immersion of the samples in an aggressive medium and the subsequent evaluation of the attack, using metallographic analysis. In order to quantity the IGC suffered by the samples, both the degree and the depth of the attacks were measured. In addition, electrochemical noise (EN) signals were recorded during the normalized tests. This technique is especially interesting for the study of corrosion processes of systems with low impedance, such as those faced in this paper, since it does not modify the corrosion potential of the system. Three parameters were used to analyse the EN signals: noise resistance (Rn) and two shot noise parameters, the characteristic charge (q) and the characteristic frequency (fn). Finally, the relationship between the results of the metallographic analysis and those obtained from the analysis of EN signals was established. Unfortunately, a poor correlation between the shot noise parameters and the degree of IGC was found, due to both the high localization and high activities of all systems.
Colecciones
  • Artículos Científicos [12014]
  • Articulos Científicos CC. Mat. [579]
  • Artículos Científicos IMEYMAT [578]
  • Artículos Científicos INBIO [422]
Attribution-NonCommercial-NoDerivatives 4.0 Internacional
Esta obra está bajo una Licencia Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 Internacional

Listar

Todo RODINComunidades y ColeccionesPor fecha de publicaciónAutoresTítulosMateriasEsta colecciónPor fecha de publicaciónAutoresTítulosMaterias

Mi cuenta

AccederRegistro

Estadísticas

Ver Estadísticas de uso

Información adicional

Acerca de...Deposita en RODINPolíticasNormativasDerechos de autorEnlaces de interésEstadísticasNovedadesPreguntas frecuentes

RODIN está accesible a través de

OpenAIREOAIsterRecolectaHispanaEuropeanaBaseDARTOATDGoogle Académico

Enlaces de interés

Sherpa/RomeoDulcineaROAROpenDOARCreative CommonsORCID

RODIN está gestionado por el Área de Biblioteca, Archivo y Publicaciones de la Universidad de Cádiz

ContactoSugerenciasAtención al Usuario