• español
    • English
  • Login
  • español 
    • español
    • English

UniversidaddeCádiz

Área de Biblioteca, Archivo y Publicaciones
Comunidades y colecciones
Ver ítem 
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
JavaScript is disabled for your browser. Some features of this site may not work without it.

Structural optimization of 3D-printed patient-specific ceramic scaffolds for in vivo bone regeneration in load-bearing defects

Thumbnail
Identificadores

URI: http://hdl.handle.net/10498/34551

DOI: 10.1016/J.JMBBM.2021.104613

ISSN: 1751-6161

Ficheros
Artículo principal (7.203Mb)
Estadísticas
Ver estadísticas
Métricas y Citas
 
Compartir
Exportar a
Exportar a MendeleyRefworksEndNoteBibTexRIS
Metadatos
Mostrar el registro completo del ítem
Autor/es
Blázquez Carmona, PabloAutoridad UCA; Sanz Herrera, José Antonio; Martínez Vázquez, Francisco Javier; Domínguez, Jaime; Reina Romo, Esther
Fecha
2021-06-11
Fuente
Journal of the Mechanical Behavior of Biomedical Materials, Vol. 121, 2021
Resumen
Tissue engineering has recently gained popularity as an alternative to autografts to stimulate bone tissue regeneration through structures called scaffolds. Most of the in vivo experiments on long-bony defects use internally-stabilized generic scaffolds. Despite the wide variety of computational methods, a standardized protocol is required to optimize ceramic scaffolds for load-bearing bony defects stabilized with flexible fixations. An optimization problem was defined for applications to sheep metatarsus defects. It covers biological parameters (porosity, pore size, and the specific surface area) and mechanical constraints based on in vivo and in vitro results reported in the literature. The optimized parameters (59.30% of porosity, 5768.91 m−1 of specific surface area, and 360.80 μm of pore size) and the compressive strength of the selected structure were validated in vitro by means of tomographic images and compression tests of six 3D-printed samples. Divergences between the design and measured values of the optimized parameters, mainly due to manufacturing defects, are consistent with the previous studies. Using the mixed experimental-mathematical scaffold-design procedure described, they could be implanted in vivo with instrumented external fixators, therefore facilitating biomechanical monitoring of the regeneration process.
Materias
Robocasting; Tissue engineering; Mathematical optimization; Bone mechanics; Finite element method
Colecciones
  • Artículos Científicos [12059]
  • Articulos Científicos Ing. Mec. [327]
Attribution-NonCommercial-NoDerivatives 4.0 Internacional
Esta obra está bajo una Licencia Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 Internacional

Listar

Todo RODINComunidades y ColeccionesPor fecha de publicaciónAutoresTítulosMateriasEsta colecciónPor fecha de publicaciónAutoresTítulosMaterias

Mi cuenta

AccederRegistro

Estadísticas

Ver Estadísticas de uso

Información adicional

Acerca de...Deposita en RODINPolíticasNormativasDerechos de autorEnlaces de interésEstadísticasNovedadesPreguntas frecuentes

RODIN está accesible a través de

OpenAIREOAIsterRecolectaHispanaEuropeanaBaseDARTOATDGoogle Académico

Enlaces de interés

Sherpa/RomeoDulcineaROAROpenDOARCreative CommonsORCID

RODIN está gestionado por el Área de Biblioteca, Archivo y Publicaciones de la Universidad de Cádiz

ContactoSugerenciasAtención al Usuario