• español
    • English
  • Login
  • español 
    • español
    • English

UniversidaddeCádiz

Área de Biblioteca, Archivo y Publicaciones
Comunidades y colecciones
Ver ítem 
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
JavaScript is disabled for your browser. Some features of this site may not work without it.

Experimental validation of a simplified CFD model for a PCM-water finned heat exchanger

Thumbnail
Identificadores

URI: http://hdl.handle.net/10498/36444

DOI: 10.1093/IJLCT/CTAE293

ISSN: 1748-1325

ISSN: 1748-1317

Ficheros
OA_2025_0059.pdf (2.081Mb)
Estadísticas
Ver estadísticas
Métricas y Citas
 
Compartir
Exportar a
Exportar a MendeleyRefworksEndNoteBibTexRIS
Metadatos
Mostrar el registro completo del ítem
Autor/es
González Gallero, Francisco JavierAutoridad UCA; González Siles, GabrielAutoridad UCA; Rodríguez Maestre, IsmaelAutoridad UCA; Foncubierta Blázquez, Juan LuisAutoridad UCA; Bottarelli, Michelle
Fecha
2025
Departamento/s
Física Aplicada; Máquinas y Motores Térmicos
Fuente
International Journal of Low-Carbon Technologies - 2025, Vol. 20 pp. 234-248
Resumen
The most widely used numerical models in the scientific literature for simulating heat exchangers with phase change materials (PCMs) and water as the heat transfer fluid, are based on computational fluid dynamics (CFD) techniques, with the modelling of phase change being the key issue. The consideration of phase change effect, as well as the resolution of the movement of the PCM in the liquid state, make CFD models computationally very expensive. However, various published experiments indicate that during the heat discharge process, the dominant heat transfer mechanism is conduction in the solidified PCM around the finned tube. For this reason, this article presents a simplified CFD model, where convective flow of the PCM is neglected during the discharge process. The model was validated experimentally, and to achieve this validation process, an experimental prototype of a one-meter-long axially finned heat exchanger with four fins was built. Inlet and outlet water temperatures were continuously recorded, along with temperatures at various points inside the PCM, under four different water flow rates. The proposed numerical model was able to predict the outlet water temperature with an error smaller than 1◦C in all cases, and to capture the observed trend in temperature inside the PCM.
Colecciones
  • Artículos Científicos [12014]
  • Articulos Científicos Fis. Ap. [317]
  • Articulos Científicos Maq. Mot. Térm. [109]
Attribution-NonCommercial-NoDerivatives 4.0 Internacional
Esta obra está bajo una Licencia Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 Internacional

Listar

Todo RODINComunidades y ColeccionesPor fecha de publicaciónAutoresTítulosMateriasEsta colecciónPor fecha de publicaciónAutoresTítulosMaterias

Mi cuenta

AccederRegistro

Estadísticas

Ver Estadísticas de uso

Información adicional

Acerca de...Deposita en RODINPolíticasNormativasDerechos de autorEnlaces de interésEstadísticasNovedadesPreguntas frecuentes

RODIN está accesible a través de

OpenAIREOAIsterRecolectaHispanaEuropeanaBaseDARTOATDGoogle Académico

Enlaces de interés

Sherpa/RomeoDulcineaROAROpenDOARCreative CommonsORCID

RODIN está gestionado por el Área de Biblioteca, Archivo y Publicaciones de la Universidad de Cádiz

ContactoSugerenciasAtención al Usuario