• español
    • English
  • Login
  • español 
    • español
    • English

UniversidaddeCádiz

Área de Biblioteca, Archivo y Publicaciones
Comunidades y colecciones
Ver ítem 
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
JavaScript is disabled for your browser. Some features of this site may not work without it.

Influence of TiC particles on the properties of AA2017 friction surfaced coatings

Thumbnail
Identificadores

URI: http://hdl.handle.net/10498/38084

DOI: 10.1007/S42114-025-01231-2

ISSN: 2522-0128

ISSN: 2522-0136

Ficheros
OA_2025_0533.pdf (2.643Mb)
Estadísticas
Ver estadísticas
Métricas y Citas
 
Compartir
Exportar a
Exportar a MendeleyRefworksEndNoteBibTexRIS
Metadatos
Mostrar el registro completo del ítem
Autor/es
Chludzinski, MarianeAutoridad UCA; Vivas, Javier; Vázquez Martínez, Juan ManuelAutoridad UCA; Sol Illana, Irene delAutoridad UCA; Begiristain, Egoitz Aldanondo
Fecha
2025-03-25
Departamento/s
Ciencia de los Materiales e Ingeniería Metalúrgica y Química Inorgánica; Ingeniería Mecánica y Diseño Industrial
Fuente
ADVANCED COMPOSITES AND HYBRID MATERIALS, Vol. 8, Núm. 2, 2025, 222
Resumen
Friction surfacing (FS) is a solid-state process employed for coatings that has demonstrated significant advancements in the manufacturing of aluminium matrix composites reinforced with ceramic particles. This study explores the effect of AA2017 aluminium consumable rods packed with titanium carbide (TiC) in the FS process applied to an AA6082 substrate. A subsequent post-processing friction stir process (FSP) was performed to further refine the distribution of ceramic particles. Analyses were conducted using light optical and scanning electron microscopy, X-ray diffractometer (XRD), microhardness, and pin-on-flat wear testing. The results demonstrated that the incorporation of TiC reinforcement significantly enhanced the FS deposition efficiency and rate by approximately 31%, without affecting rod consumption. Initially, the TiC particles were distributed in layers parallel to the substrate surface, but the FSP technique dispersed them throughout the aluminium matrix. In terms of mechanical properties, the reinforcement increased microhardness by 13.6% and reduced wear resistance (wear volume) by 13%. Notably, the FSP process enhanced wear resistance, reducing wear volume by 48% compared to the TiC-free coating, while also mitigating the hardness increase caused by the FS process. Additionally, XRD analysis indicated that neither FS nor FSP generated new phases, indicating no interaction between the aluminium matrix and the ceramic reinforcements.
Materias
Friction surfacing ; Friction stir process; Metal matrix composites ; TiC reinforcement ; Hardness; Wear mechanisms
Colecciones
  • Artículos Científicos [12077]
Attribution-NonCommercial-NoDerivatives 4.0 Internacional
Esta obra está bajo una Licencia Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 Internacional

Listar

Todo RODINComunidades y ColeccionesPor fecha de publicaciónAutoresTítulosMateriasEsta colecciónPor fecha de publicaciónAutoresTítulosMaterias

Mi cuenta

AccederRegistro

Estadísticas

Ver Estadísticas de uso

Información adicional

Acerca de...Deposita en RODINPolíticasNormativasDerechos de autorEnlaces de interésEstadísticasNovedadesPreguntas frecuentes

RODIN está accesible a través de

OpenAIREOAIsterRecolectaHispanaEuropeanaBaseDARTOATDGoogle Académico

Enlaces de interés

Sherpa/RomeoDulcineaROAROpenDOARCreative CommonsORCID

RODIN está gestionado por el Área de Biblioteca, Archivo y Publicaciones de la Universidad de Cádiz

ContactoSugerenciasAtención al Usuario