• español
    • English
  • Login
  • español 
    • español
    • English

UniversidaddeCádiz

Área de Biblioteca, Archivo y Publicaciones
Comunidades y colecciones
Ver ítem 
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
  •   RODIN Principal
  • Producción Científica
  • Artículos Científicos
  • Ver ítem
JavaScript is disabled for your browser. Some features of this site may not work without it.

Texture in ITO films deposited at oblique incidence by ion beam sputtering

Thumbnail
Identificadores

URI: http://hdl.handle.net/10498/27556

DOI: 10.1016/j.apsusc.2022.154677

ISSN: 0169-4332

Ficheros
APC_2022_110.pdf (9.160Mb)
Estadísticas
Ver estadísticas
Métricas y Citas
 
Compartir
Exportar a
Exportar a MendeleyRefworksEndNoteBibTexRIS
Metadatos
Mostrar el registro completo del ítem
Autor/es
Lacroix, BertrandAutoridad UCA; Paumier, F.; Santos Izquierdo-Bueno, Antonio JesúsAutoridad UCA; Maudet, F.; Girardeau, T.; Dupeyrat, C.; García Roja, RafaelAutoridad UCA; Morales Sánchez, Francisco MiguelAutoridad UCA
Fecha
2022-12
Departamento/s
Ciencia de los Materiales e Ingeniería Metalúrgica y Química Inorgánica
Fuente
Applied Surface Science, Vol. 605
Resumen
Texture of crystalline In2O3:Sn (ITO) thin films prepared by combining ion beam sputtering (IBS) at room temperature and oblique angle deposition (OAD) has been studied depending on the vapor incidence on Si substrates (alpha, ranging from 50 degrees to 85 degrees) and the ions used to sputter the target (argon or xenon accelerated at 1.2 keV). Films obtained using Xe ions show an unusual evolution depending on the deposition angle alpha, with the development of a dual biaxial (1 1 1) off-axis texture for alpha <= 70 degrees, and a switching in the preferred out-of-plane orientation from [1 1 1] to [0 0 1] for alpha > 70 degrees that leads to a biaxial (0 0 1) texture at highest deposition angles. These behaviors are well described by mechanisms involving a maximization of the direct capture of the adatoms on {1 1 1} planes, which can however be hindered when mobilities are exalted such as in the case of Ar deposition. The tuning of adatoms mobilities through the IBS process mixed with the control of the deposition angle offered by the OAD geometry appears as an efficient route to achieve an upgraded texture engineering in nanostructured ITO thin films.
Materias
Indium tin oxide; Ion beam sputtering; Oblique angle deposition; Thin films; Texture; Morphology
Colecciones
  • Artículos Científicos [12034]
  • Articulos Científicos CC. Mat. [585]
  • Artículos Científicos IMEYMAT [581]
Atribución-NoComercial 4.0 Internacional
Esta obra está bajo una Licencia Creative Commons Atribución-NoComercial 4.0 Internacional

Listar

Todo RODINComunidades y ColeccionesPor fecha de publicaciónAutoresTítulosMateriasEsta colecciónPor fecha de publicaciónAutoresTítulosMaterias

Mi cuenta

AccederRegistro

Estadísticas

Ver Estadísticas de uso

Información adicional

Acerca de...Deposita en RODINPolíticasNormativasDerechos de autorEnlaces de interésEstadísticasNovedadesPreguntas frecuentes

RODIN está accesible a través de

OpenAIREOAIsterRecolectaHispanaEuropeanaBaseDARTOATDGoogle Académico

Enlaces de interés

Sherpa/RomeoDulcineaROAROpenDOARCreative CommonsORCID

RODIN está gestionado por el Área de Biblioteca, Archivo y Publicaciones de la Universidad de Cádiz

ContactoSugerenciasAtención al Usuario